Hall Panel Node CANsmall CS08: Difference between revisions

From CANopen-Lift
Jump to navigation Jump to search
 
(26 intermediate revisions by 2 users not shown)
Line 1: Line 1:
Ruftableauknoten CANsmall CS08
Hall Call Panel node CANsmall CS08




Line 6: Line 6:


=Profil=
=Profil=
CiA-417 (hier fehlt noch der Link zum Molex Stecker)
CiA-417


----
=Description=


=Description=
The CANsmall CS08 has 8 I/O terminals, 8 output terminals and contains the following virtual devices: Input Panel Unit and Output Panel Unit.
Der CANsmall CS08 verfügt über 8 In- Outputklemmen und beinhaltet die virtuellen Geräte Input Panel Unit und Output Panel Unit. Die In- und Outputklemmen können als Rufe, Eingänge und als Ausgänge konfiguriert werden. Somit werden beliebige Eingangssignale eingelesen und als Eingangsfunktion auf dem CAN-Bus gesendet. Ausgangssignale auf dem CAN-Bus von den einzelnen Aufzugssteuerungen werden als Ausgangsfunktion empfangen und an den Ausgangsklemmen ausgegeben.
The I/O terminals can be used for the calls, inputs- and outputs. So any input signal can be read in and sent to the CAN Bus as input-function. Also the output signals of the different lift controllers are read out via the I/O terminals or respectively output terminals.


Einsatzgebiet des CANsmall CS08 ist der Anschluss der Außentableaus von Aufzügen.
The CANsmall CS08 is used for the connection of landing fixtures for lifts. It is available for face plate mounting or quick fastening.
Der CANsmall CS08 ist je nach Ausführung als Frontplatten- oder Montafixmontage lieferbar.


Geringe Abmessung ca. 55 x 35 mm.
Small dimensions approx. 55 x 35 mm.
Keine DIP-Schalter oder Jumper erforderlich.
No DIP switches or jumper necessary.
Knotennummer und Baudrate ist konfigurierbar.
Node number and Baudrate are adjustable.
Autobauderkennung möglich.
Auto baud detection is possible.


Schaltelemente mit Quittierung sind in 3-Draht oder 4-Draht Technik gem. Kathode anschließbar.
Switching elements with recall light are connectable in 3- or 4-wire technology, common cathode.  
Das Einlesen des Eingangs bei gesetztem Ausgang ist bei beiden Anschlussvarianten möglich.
An input will be detected while the corresponding output ist set. This is possible at both wire techlologies.<br />
<br />


----
Following version are available:
Following version are available:
 
*CANsmall CS08 VST 4p (Vertical clamps, 4 slots up to 2 I/O-clamps per slot)
 
*CANsmall CS08 HST 4p (Horizontal clamps, 4 slots up to 2 I/O-clamps per slot)
*CANsmall CS08_xST (4 slots up to 2 I/O-clamps per slot)
*CANsmall CS08 VPM 4p (Vertical clamps, 1 slot f. SCHAEFER Display)
**CANsmall CS08_VST (Vertical clamps)
*CANsmall CS08 HPM 4p (Horizontal clamps, 1 slot f. SCHAEFER Display)<br />
**CANsmall CS08_HST (Horizontal clamps)
 
 
*CANsmall CS08_xPM (1 slot f. Schaefer Diplay)
**CANsmall CS08_VPM (Vertical clamps)
**CANsmall CS08_HPM (Horizontal clamps)<br />
<br />
<br />


=Topology=
=Topology=
Die Ruftableaus sind komplett vorverdrahtet von der Fa. SCHAEFER GmbH zu beziehen.
The completley pre-wired LOP's can be bought at SCHAEFER GmbH.
Eine Verdrahtung von Komponenten außerhalb des Ruftableaus ist nicht vorgesehen.
A pre-wiring of components outside the LOP's is not foreseen.  
Die komplette Schacht-Verdrahtung beschränkt sich ausschließlich auf die
The complete shaft pre-wiring is restricted exclusively to the BUS cable and the power supply.  
Busleitung und Stromversorgung.
The sequence of the LOP's is negligible seen from a logical point of view.
Die Reihenfolge der Ruftableaus ist unter logischen Gesichtspunkten unerheblich.
Thereby, potential sources of error in shaft pre-wiring are almost impossible.<br />
Hierdurch sind potentielle Fehlerquellen bei der Schachtverdrahtung nahezu ausgeschlossen.<br />
<br />
<br />


=State=
=State=
Following version are deliverable:
Following version are deliverable:
*CS08_VST
*CS08 VST 4p
*CS08_VPM
*CS08 VPM 4p
*CS08_HST
*CS08 HST 4p
*CS08_HPM<br />
*CS08 HPM 4p<br />
<br />
<br />


=Picture CANsmall CS08_VST=
=Picture CANsmall CS08 VST 4p=


[[Image:CS08_VST.jpg]]
[[Image:CS08_VST.jpg|360px]]


=Picture CANsmall CS08_VPM=
=Picture CANsmall CS08 VPM 4p=


[[Image:CS08_VPM.jpg]]
[[Image:CS08_VPM.jpg|360px]]


=Picture CANsmall CS08_HST=
=Picture CANsmall CS08 HST 4p=


[[Image:CS08_HST.jpg]]
[[Image:CS08_HST.jpg|360px]]


=Picture CANsmall CS08_HPM=
=Picture CANsmall CS08 HPM 4p=


[[Image:CS08_HPM.jpg]]
[[Image:CS08_HPM.jpg|360px]]




[[Category: Products CiA-417]]
[[Category: Products CiA-417]]

Latest revision as of 16:19, 13 August 2015

Hall Call Panel node CANsmall CS08


Manufacturer

SCHAEFER GmbH

Profil

CiA-417

Description

The CANsmall CS08 has 8 I/O terminals, 8 output terminals and contains the following virtual devices: Input Panel Unit and Output Panel Unit. The I/O terminals can be used for the calls, inputs- and outputs. So any input signal can be read in and sent to the CAN Bus as input-function. Also the output signals of the different lift controllers are read out via the I/O terminals or respectively output terminals.

The CANsmall CS08 is used for the connection of landing fixtures for lifts. It is available for face plate mounting or quick fastening.

Small dimensions approx. 55 x 35 mm. No DIP switches or jumper necessary. Node number and Baudrate are adjustable. Auto baud detection is possible.

Switching elements with recall light are connectable in 3- or 4-wire technology, common cathode. An input will be detected while the corresponding output ist set. This is possible at both wire techlologies.

Following version are available:

  • CANsmall CS08 VST 4p (Vertical clamps, 4 slots up to 2 I/O-clamps per slot)
  • CANsmall CS08 HST 4p (Horizontal clamps, 4 slots up to 2 I/O-clamps per slot)
  • CANsmall CS08 VPM 4p (Vertical clamps, 1 slot f. SCHAEFER Display)
  • CANsmall CS08 HPM 4p (Horizontal clamps, 1 slot f. SCHAEFER Display)


Topology

The completley pre-wired LOP's can be bought at SCHAEFER GmbH. A pre-wiring of components outside the LOP's is not foreseen. The complete shaft pre-wiring is restricted exclusively to the BUS cable and the power supply. The sequence of the LOP's is negligible seen from a logical point of view. Thereby, potential sources of error in shaft pre-wiring are almost impossible.

State

Following version are deliverable:

  • CS08 VST 4p
  • CS08 VPM 4p
  • CS08 HST 4p
  • CS08 HPM 4p


Picture CANsmall CS08 VST 4p

Picture CANsmall CS08 VPM 4p

Picture CANsmall CS08 HST 4p

Picture CANsmall CS08 HPM 4p

Retrieved from "https://en.canopen-lift.org/index.php?title=Hall_Panel_Node_CANsmall_CS08&oldid=4427"