Panel Node CANnode CN16: Difference between revisions

From CANopen-Lift
Jump to navigation Jump to search
 
(47 intermediate revisions by 4 users not shown)
Line 1: Line 1:
[[de:Tableauknoten_CANnode_CN16]]
[[de:Tableauknoten_CANnode_CN16]]
{{translation}}
= Manufacturer =
= Manufacturer =
[[Schaefer GmbH|SCHAEFER GmbH]]
[[Schaefer GmbH|SCHAEFER GmbH]]


=Profil=
=Profil=
CiA DSP417
CiA-417


= Description =
= Description =
Der CANnode CN16 verfügt über 8 In- Outputklemmen, 8 Outputklemmen und beinhaltet die virtuellen Geräte Input Panel Unit und Output Panel Unit. Die In- und Outputklemmen können als Rufklemmen und die Outputklemmen als reine Ausgangsklemmen benutzt werden. Somit werden beliebige Eingangssignale eingelesen und als Eingangsfunktion auf dem CAN-Bus gesendet bzw. Ausgangssignale von den einzelen Aufzugssteuerungen an den In-Outputklemmen bzw. Outputklemmen ausgegeben.
The CANnode CN16 has 8 I/O terminals, 8 output terminals and contains the following virtual devices: Input Panel Unit and Output Panel Unit.
The I/O terminals can be used for the calls and the output terminals as pure outputs. So any input signal can be read in and sent to the CAN Bus as input-function. Also the output signals of the different lift controllers are read out via the I/O terminals or respectively output terminals.


Einsatzgebiet des CANnode CN16 ist der Anschluss von Innen- und Außentableaus von Aufzügen.
The CANnode CN16 is used for the connection of car and landing fixtures for lifts. It is available for face plate and wall mounting as well as for top hat rail mounting.
Der CANnode CN16 ist je nach Ausführung als Front-, Wand- oder Hutschienmontage lieferbar.
<br />
Dimensions approx. 72 x 65 mm. Node-ID and Baudrate are adjustable by DIP switches.<br />
Autobaud detection is possible.
 
Switching elements with recall light are connectable in 3- or 4-wire technology, common cathode.
An input will be detected while the corresponding output ist set. This is possible at both wire techlologies.
 
Following versions are available:
*CANnode CN16 VST 4p (Vertical Clamps; 8 I/O-Clamps; 8 O-Clamps)
*CANnode CN16 VPM 4p (Vertical Clamps; 8 I/O-Clamps; 1 Interface f. SCHAEFER Display))<br />
<br />
 
=Topology=
The completley pre-wired LOP's can be bought at SCHAEFER GmbH.
A pre-wiring of components outside the LOP's is not foreseen.
The complete shaft pre-wiring is restricted exclusively to the BUS cable and the power supply.
The sequence of the LOP's is negligible seen from a logical point of view.
Thereby, potential sources of error in shaft pre-wiring are almost impossible.<br />
<br />


=State=
=State=
Available
Following versions are available
*CN16 VST 4p
**optional Wall monting CN16 VST 4p -W
**optional Top-hat rail mounting CN16 VST 4p -H
*CN16 VPM 4p
**optional Wall monting CN16 VPM 4p -W
**optional Top-hat rail mounting CN16 VPM 4p -H
*CN16 HST 4p
*CN16 HPM 4p<br />
<br />
 
= Picture CANnode CN16 VST 4p =
[[Image:CN16_VST_4p_320x385.jpg|360px]]
 
= Picture CANnode CN16 VPM 4p=
[[Image:CN16_VPM_4p_320x385.jpg|360px]]
 
= Picture CANnode CN16 HST 4p =
[[Image:CN16_HST_4p_320x385.jpg|360px]]


= Picture =
= Picture CANnode CN16 HPM 4p =
[[Image:SCHAEFER_CN16VST.jpg]]
[[Image:CN16_HPM_4p_320x385.jpg|360px]]


[[Category: Products DSP417]]
[[Category: Products CiA-417]]

Latest revision as of 16:29, 13 August 2015

Manufacturer

SCHAEFER GmbH

Profil

CiA-417

Description

The CANnode CN16 has 8 I/O terminals, 8 output terminals and contains the following virtual devices: Input Panel Unit and Output Panel Unit. The I/O terminals can be used for the calls and the output terminals as pure outputs. So any input signal can be read in and sent to the CAN Bus as input-function. Also the output signals of the different lift controllers are read out via the I/O terminals or respectively output terminals.

The CANnode CN16 is used for the connection of car and landing fixtures for lifts. It is available for face plate and wall mounting as well as for top hat rail mounting.
Dimensions approx. 72 x 65 mm. Node-ID and Baudrate are adjustable by DIP switches.
Autobaud detection is possible.

Switching elements with recall light are connectable in 3- or 4-wire technology, common cathode. An input will be detected while the corresponding output ist set. This is possible at both wire techlologies.

Following versions are available:

  • CANnode CN16 VST 4p (Vertical Clamps; 8 I/O-Clamps; 8 O-Clamps)
  • CANnode CN16 VPM 4p (Vertical Clamps; 8 I/O-Clamps; 1 Interface f. SCHAEFER Display))


Topology

The completley pre-wired LOP's can be bought at SCHAEFER GmbH. A pre-wiring of components outside the LOP's is not foreseen. The complete shaft pre-wiring is restricted exclusively to the BUS cable and the power supply. The sequence of the LOP's is negligible seen from a logical point of view. Thereby, potential sources of error in shaft pre-wiring are almost impossible.

State

Following versions are available

  • CN16 VST 4p
    • optional Wall monting CN16 VST 4p -W
    • optional Top-hat rail mounting CN16 VST 4p -H
  • CN16 VPM 4p
    • optional Wall monting CN16 VPM 4p -W
    • optional Top-hat rail mounting CN16 VPM 4p -H
  • CN16 HST 4p
  • CN16 HPM 4p


Picture CANnode CN16 VST 4p

Picture CANnode CN16 VPM 4p

Picture CANnode CN16 HST 4p

Picture CANnode CN16 HPM 4p

Retrieved from "https://en.canopen-lift.org/index.php?title=Panel_Node_CANnode_CN16&oldid=4433"