Panel Node CANnode CN16: Difference between revisions
RSbySCHÄFER (talk | contribs) No edit summary |
|||
| (21 intermediate revisions by 2 users not shown) | |||
| Line 18: | Line 18: | ||
An input will be detected while the corresponding output ist set. This is possible at both wire techlologies. | An input will be detected while the corresponding output ist set. This is possible at both wire techlologies. | ||
Following versions are available: | |||
*CANnode CN16 VST 4p (Vertical Clamps; 8 I/O-Clamps; 8 O-Clamps) | |||
CANnode | *CANnode CN16 VPM 4p (Vertical Clamps; 8 I/O-Clamps; 1 Interface f. SCHAEFER Display))<br /> | ||
CANnode | |||
<br /> | <br /> | ||
| Line 32: | Line 30: | ||
Thereby, potential sources of error in shaft pre-wiring are almost impossible.<br /> | Thereby, potential sources of error in shaft pre-wiring are almost impossible.<br /> | ||
<br /> | <br /> | ||
=State= | =State= | ||
Following versions are available | Following versions are available | ||
* | *CN16 VST 4p | ||
**optional Wall monting | **optional Wall monting CN16 VST 4p -W | ||
**optional Top-hat rail mounting | **optional Top-hat rail mounting CN16 VST 4p -H | ||
* | *CN16 VPM 4p | ||
**optional Wall monting | **optional Wall monting CN16 VPM 4p -W | ||
**optional Top-hat rail mounting | **optional Top-hat rail mounting CN16 VPM 4p -H | ||
* | *CN16 HST 4p | ||
* | *CN16 HPM 4p<br /> | ||
<br /> | <br /> | ||
= Picture CANnode | = Picture CANnode CN16 VST 4p = | ||
[[Image: | [[Image:CN16_VST_4p_320x385.jpg|360px]] | ||
= Picture CANnode | = Picture CANnode CN16 VPM 4p= | ||
[[Image: | [[Image:CN16_VPM_4p_320x385.jpg|360px]] | ||
= Picture CANnode | = Picture CANnode CN16 HST 4p = | ||
[[Image: | [[Image:CN16_HST_4p_320x385.jpg|360px]] | ||
= Picture CANnode | = Picture CANnode CN16 HPM 4p = | ||
[[Image: | [[Image:CN16_HPM_4p_320x385.jpg|360px]] | ||
[[Category: Products CiA-417]] | [[Category: Products CiA-417]] | ||
Latest revision as of 15:29, 13 August 2015
Manufacturer
Profil
CiA-417
Description
The CANnode CN16 has 8 I/O terminals, 8 output terminals and contains the following virtual devices: Input Panel Unit and Output Panel Unit. The I/O terminals can be used for the calls and the output terminals as pure outputs. So any input signal can be read in and sent to the CAN Bus as input-function. Also the output signals of the different lift controllers are read out via the I/O terminals or respectively output terminals.
The CANnode CN16 is used for the connection of car and landing fixtures for lifts. It is available for face plate and wall mounting as well as for top hat rail mounting.
Dimensions approx. 72 x 65 mm. Node-ID and Baudrate are adjustable by DIP switches.
Autobaud detection is possible.
Switching elements with recall light are connectable in 3- or 4-wire technology, common cathode. An input will be detected while the corresponding output ist set. This is possible at both wire techlologies.
Following versions are available:
- CANnode CN16 VST 4p (Vertical Clamps; 8 I/O-Clamps; 8 O-Clamps)
- CANnode CN16 VPM 4p (Vertical Clamps; 8 I/O-Clamps; 1 Interface f. SCHAEFER Display))
Topology
The completley pre-wired LOP's can be bought at SCHAEFER GmbH.
A pre-wiring of components outside the LOP's is not foreseen.
The complete shaft pre-wiring is restricted exclusively to the BUS cable and the power supply.
The sequence of the LOP's is negligible seen from a logical point of view.
Thereby, potential sources of error in shaft pre-wiring are almost impossible.
State
Following versions are available
- CN16 VST 4p
- optional Wall monting CN16 VST 4p -W
- optional Top-hat rail mounting CN16 VST 4p -H
- CN16 VPM 4p
- optional Wall monting CN16 VPM 4p -W
- optional Top-hat rail mounting CN16 VPM 4p -H
- CN16 HST 4p
- CN16 HPM 4p
Picture CANnode CN16 VST 4p
Picture CANnode CN16 VPM 4p
Picture CANnode CN16 HST 4p
Picture CANnode CN16 HPM 4p
